<img alt="" src="https://www.365operation.com/807202.png" style="display:none;">

Routing Secondary Pan Drains Through a Cold Attic

Routing Secondary Pan Drains Through a Cold Attic

A secondary drain line can sit dry for months, then be needed on one of the coldest nights of the year. By then, water trapped in a sag or ice forming at the outlet may have blocked the line. In an unconditioned attic, the primary and secondary drains may follow similar routes through the coldest areas, leaving both vulnerable to freezing temperatures.

The drain's ability to function in freezing weather depends in part on decisions made during installation. Where the line leaves the pan, how far it travels through the coldest parts of the attic, and whether water can collect along the way all affect its ability to drain when needed.

Condensing Furnaces Bring Winter Drainage Risks

A heat pump's indoor coil generally doesn't produce condensate in heating mode, but a high-efficiency condensing furnace produces it throughout the winter. That means the furnace's primary condensate drain may be carrying water during the coldest weather of the year.

If the primary drain freezes, condensate can back up and, depending on the system's configuration, reach the secondary pan. That makes it important to consider whether the secondary drain will remain open under the same conditions.

Water left in a low spot from an earlier overflow can also freeze, blocking the secondary drain even if it hasn't carried water recently. Condensate that collects in a sag in the line after an earlier overflow can freeze and remain there until temperatures rise. The line may appear clear at the pan while an ice plug farther along prevents water from reaching the exterior.

The Eaves Are Often the Most Vulnerable Part of the Route

An attic isn't uniformly cold. Near the eaves, outdoor air entering through soffit vents can keep temperatures lower than in areas farther inside. A drain line that follows the perimeter of the attic may spend much of its run in those colder conditions.

Piping laid across the top of attic insulation is also exposed. And when a long horizontal run develops a sag between supports, the water collecting there has more time to freeze.

The termination introduces another concern. If water drips from the outlet during freezing weather, ice can gradually accumulate around the opening until the drain is restricted or completely blocked.

Keeping the line farther from the eaves for most of its run can reduce exposure. A shorter route also means less piping to support and fewer opportunities for a low spot to develop. But the shortest practical route isn't always available when the pan has only one drain outlet.

Drain Port Placement Affects Routing Options

With a single fixed port, the drain has to leave the pan wherever the manufacturer positioned the outlet. That can be inconvenient when the port faces away from the exterior wall or the most protected path through the attic.

The installer may have to run the line around the air handler before heading toward the termination. That adds pipe and fittings, particularly when the equipment is positioned close to framing or other obstructions. Every change in direction also makes it more difficult to maintain a consistent slope without creating a low spot.

Drilling another outlet in the field may provide a more direct route, but the new connection has to be sealed properly to avoid introducing a leak.

DuraPlas designed its PolarPan HVAC Pan with pre-plumbed drain ports on both the long and short sides. Contractors can use the outlet that faces the preferred route and close the unused port.

That choice eliminates unnecessary piping around the equipment and allows the drain to head toward a more protected area of the attic. The pan's reinforced construction helps it maintain its shape, while designated strap attachment areas provide secure mounting points.

Keeping the Line Away From the Coldest Areas

Once the drain leaves the pan, its route should preserve a continuous downward slope while limiting exposure to freezing temperatures.

Running the line farther inside the attic, rather than along the perimeter, can help. Where the installation allows, piping can be routed within attic insulation before approaching the eave near the termination. That keeps more of the run away from the cold outdoor air entering through soffit vents.

Long horizontal runs deserve particular attention. Even with adequate slope at installation, widely spaced supports can allow piping to sag over time. Water left in those low spots can freeze, so maintaining the slope between supports matters as much as establishing it initially.

Some exposed piping may be unavoidable. Insulation can help reduce heat loss, and in colder climates, self-regulating heat cable approved for use with plastic piping may provide additional protection where appropriate.

The termination still needs to be conspicuous so occupants can recognize a drainage problem. It should also be positioned where dripping water won't create an ice hazard or allow ice buildup to block the outlet.

Where the risk of freezing is substantial, a compatible water-level shutoff switch adds protection. If water rises in the secondary pan, the switch can stop equipment operation even if ice prevents the drain from carrying water away.

Fall Is the Best Time to Catch Routing Problems

A fall service visit is an opportunity to inspect the secondary drainage system before freezing weather arrives.

Water already in the pan may indicate a problem with the primary drain. Along the secondary line, contractors can look for low spots, deteriorated supports, or insulation that has been displaced. The termination should be open, and any installed float switch should trip when tested.

A drain that appears unobstructed in mild weather may still have sections vulnerable to freezing. Finding those sections before the first hard freeze gives contractors a chance to correct the route while the piping is dry and accessible.

About DuraPlas

DuraPlas

For more than 50 years, DuraPlas has introduced and perfected plastic solutions for industries spanning the globe. From agriculture to energy, we strive to make your work easier and more cost effective.

Get in Touch

With a solutions expert