Of all the components involved in an HVAC installation, the drip pan might be the least talked about—and one of the most consequential when it fails.
Tucked beneath an evaporator coil or air handler, the pan is there for one purpose: to catch and direct condensation away from the unit and out of the building. When it works, it’s invisible. When it fails, it becomes a major issue—one that often leads to costly callbacks, damage claims, and frustrated customers.
Yet many installers still treat the drip pan as an afterthought, opting for the cheapest option available—almost always metal—and assuming “it’ll be fine.” But over time, inferior pans can crack, warp, or clog—resulting in standing water, slow leaks, and major damage.
Let’s take a closer look at why metal drip pans fail, what signs to watch for, and why the right upgrade—like the PolarPan from DuraPlas—can protect your installs, your time, and your reputation.
At install time, a metal pan may seem like a solid choice. But once the system’s been running for a few weeks—or a full cooling season—problems begin to surface.
Even galvanized metal is vulnerable to oxidation—especially once the protective coating gets scratched or exposed to standing water. In humid attics, near ocean air, or inside utility closets, metal pans begin to pit and corrode from the inside out.
That rust isn’t just cosmetic. It can eat through the pan over time, weaken structural edges, and cause visible staining on surrounding walls or floors.
Metal doesn’t just rust—it bends. In high-heat environments (like unconditioned attics), metal drip pans can expand, warp, or sag. This distortion changes drainage angles and leads to noise issues—rattling, vibration, or metal-on-metal contact that customers are quick to notice.
Many sheet-metal pans are fabricated flat or without proper slope. That leads to ponding condensate in corners, which encourages algae and mold, especially in systems with long horizontal drain runs.
Most pan failures don’t show up right away. They develop quietly—until a homeowner sees a ceiling stain, smells mildew, or notices that water isn’t draining correctly. And when that happens, it’s the contractor who gets called back, not the manufacturer.
Even if the coil, lineset, and disconnect were installed perfectly, a failed pan can undermine the entire job.
PolarPan is built to solve these problems before they happen. Made from high-density polyethylene using injection molding—not thin metal sheet or fiberboard—it’s engineered for long-term durability in the toughest HVAC environments.
Here’s what sets it apart:
Rust-Free Performance
Polyethylene doesn’t corrode—ever. PolarPan can sit in condensate, operate in humid climates, and handle high-temperature attics without rusting, pitting, or weakening over time.
Injection-molded ribbing gives PolarPan rigidity where it’s needed most—at corners, across the base, and along mounting points. It holds up under heavy units without bowing or flexing, providing consistent support that stays level over time, even in demanding conditions.
No rattling. No drumming. No creaks. Polyethylene naturally dampens vibration from system startup, helping reduce the noise that metal pans often amplify.
PolarPan sizes align with common coil footprints and come in multiple configurations for various install types. It drills clean, straps easily, and holds up to pressure washing without degrading.
While it’s a great upgrade for any install, PolarPan shines in situations where metal pans are most vulnerable:
For HVAC distributors, PolarPan offers a value-added accessory that:
It’s not a luxury upgrade—it’s a risk management tool that benefits both the installer and the customer.
The cost of a callback—even just one—can easily outweigh the impact of using a lower-performing pan. Water damage, service time, and lost trust add up fast. Choosing a more reliable drip pan from the start helps prevent those issues before they begin.
If you’re going to spend hours installing and charging a system, doesn’t it make sense to build on a foundation you can trust?
Metal drip pans aren’t holding up like they used to. In today’s field conditions—with tighter installs, more humidity, and higher homeowner expectations—it’s not enough to just meet the minimum.
PolarPan is a modern solution for modern HVAC installs: clean, corrosion-proof, engineered to drain, and built to last.
When it comes to callbacks, the best ones are the ones that never happen. Start preventing them at the bottom—with the right pan.